Livestock Trailer - 2020 EBY Wrangler 8' X 24' 16K Wrangler


M.H.EBY  WRANGLER 24’ X  8' X 7'

24' long x 8' wide x 7' tall, 2 8000 lb. Oil bath Torsion brake axles, LR-G tires including spare, front rolling gate and divider gate with slider between fenders, full swing rear gate with slider, front Gooseneck drop gate, side running board/step. led lights, 2 interior led lights, 2 closeable front vents,  LED reverse lights,   Stock # GWL2476


The industry's only "commercial grade" production model livestock trailer.

 Standard features:


- Floor Length: 24”

Outside Width: 8’ 6”

Inside Height: 7’2"

Running Gear:

- GVWR: 15,000 lbs.

- Axles: (2) 7,000# rubber ride

- Tires: (4) ST235/85R16 steel belted radials, load range E.

- Brakes: 12" x 2" electric on 7K Axles.

- Safety Equip.: Two chains and electronic breakaway kit.

- Landing Gear: Single drop leg, single speed, roadside crank with crank bushing

Nose Construction:

- Front Nose Assembly: 9º tapered nose with .080 aluminum smooth sheet sides and front, with aerodynamic aluminum corner caps and extruded front corner posts.

- Posts: 4-1/2" extruded aluminum hat shaped posts.

- Bottom Rails: 8" extruded aluminum. (9-1/2?on tri-axle)

- Crossmembers: 3" extruded aluminum I-beams on 12" centers.

- Floor: 1/8" aluminum smooth sheet.

- Upper Coupler: 3/16" x 5" x 5" tubular steel. (5/16?x 5?x 7?tubular steel on tri-axle)

- Lower Coupler: 2-5/16" ball coupler (20,000# ball rating) (30,000# ball rating on tri-axle) with steel hitch post section and aluminum front gusset, adjustable height 28" – 36-1/2" from ground to top of ball.


Box Construction:

- Slat sides.

- Posts: Extruded aluminum, 1" x 3" tapered tubular side posts, spaced on 18" centers maximum.

- Bottom Rails: 12" extruded aluminum.

- Top Rails: 6" extruded aluminum.

- Crossmembers: 3" extruded aluminum I-beams on 12" centers with 3" extruded aluminum J-beams at floor seams.

- Floor: .115 6061 T6 aluminum diamond plate with (4) 1" high ridges, corrugated longitudinally on 19" centers.

- Side Door: 33" wide, curb side, 10-3/4" from drop sheet up to 26'models.

- Rear Frame Assembly: 3" x 5" tubular extruded aluminum with Eby cast aluminum corner caps.

- Rear Door: Full swing with (3) 4" extruded aluminum offset hinges for extended swing radius. Hinges are mechanically fastened and welded to rear frame. 32" wide exterior sliding door on roadside with polyurethane rollers at the top and UHMW wear pads at the threshold.

Roof Assembly:

- Sheet: One-piece .040 aluminum externally riveted to top rail on 4" centers.

Bows: Arched, hat shaped 1-1/2" x 4" extruded aluminum on 24" centers.


-Std. Partition: Extruded aluminum tube and punched sheet construction with (2) horizontal stiffener rails and outside release slam latch. Extruded aluminum pipe hinge with nylon bushing mounted curbside. Partition located on post aprox. 10’ from rear. w/slide door in it. Second center gate is mounted on rollers and adjustable.

- Nose Partition: Bottom hinged, punched sheet construction with (2) self-catching rotary latches.

Lights & Wiring:

- Lights: 12-volt D.O.T. approved, LED.

- Wiring: A.T.A. color coded, wiring harness.

- Rear Lights: Modular, turn-tail-stop, LED. One light each side (red).

- Inside Lights: Two LED, with external rear water resistant switch.

(Meets all US and Canadian Regulations.)


- Tire Carrier: Aluminum, mounted on exterior drop sheet.

- Fenders: Extruded rolled aluminum.

- Bumpers: Full width 3" molded rubber.

- Skid Plates: (3) 3/16" formed aluminum.

- Paint: Steel parts painted silver.

- Conspicuity Tape: Meets all US and Canadian regulations

Primary Information
Stock #GWL2476
ManufacturerM.H. Eby
Floorplan8' X 24' 16K Wrangler
TypeLivestock Trailer
Length24' 0"
Width8' 0"
Height7' 0"
LocationHalsey, Oregon
Primary Information
Floor TypeAluminum
Rear OpeningSingle Rear
Load TypeStraight
GVWR16,000 lbs
Dry Weight4,640 lbs
Trailer Weight4,640 lbs
Payload Capacity11,360 lbs

Contact Seller

You May Also Like